Steel/Fe Adhesive Wheel Balance Weights F180

Find HOPSON TYRE REPAIR® @ Essen 2016 in Germany during May.24-27, 2016.

Booth Number.: 11H26

 

We are now looking for worldwide agents for HOPSON TYRE REPAIR. If you are interested, please contact us today.

 

General Info:

 

Part No.: F180

Height:3.0mm(include tape 4.0mm)

Width:19mm

Length:194mm

Packing: 52strips/box, 4box/ctn

                  

Description:

 

HOPSON POWER WEIGHT offers a complete range of quality coated, non-coated and adhesive Wheel Weights for passenger cars, motorcycles and trucks. HOPSON Coated Wheel Weights are polyester coated(silver-grey) to prevent material staining on the alloy wheel. HOPSON adhesive wheel weights are pre-cut and require no additional cutting. A simplified organizational system makes wheel weight selection and application easy. Our goal is to become a partner, not just a product supplier. HOPSON POWER WEIGHT guarantee that its products will meet and exceed the highest quality standards in the industry. We are committed to ensuring your success.

 

The steel adhesive strip is individually separable and made up of 12x1/4oz segments.

 

Surface: Zinc plated and Epoxy coated is avaliable.

Installation of Adhesive Weights:

 

Pre-treating the rim:

Clean the rim thoroughly with a cleaning agent that is compatible with varnish(e.g. IPA 70%) in order to remove any residual grease, silicone or adhesive.

Please note: A minimum of 15ºC is required in terms of both the room temperature and the rim temperature.

 

Pre-bending the weights:

Separate the correct gram(as calculated) from the bar. Mould the shape of the weight to match the rim radius(with protective film).

Please note: You need to bend the weights gradually, otherwise they will break apart at the joins. You should bend the weight to a little more than the rim's radius.

 

Removal of the protective film:

Remove the protective film.

Please note: Do not touch the glued surface after peeling off the rim.

 

Sticking the weight on:

Attached the weight to the calculated point on the rim, making sure that the weight is distributed evenly either side and the weight is parallel with the edge of the rim.

Please note: Press down on the weight hard, working from the centre to the left and right. A minimum pressure of 1kg/cm2 is required. The angle of the sticking surface should not be higher than 15 ºC to normal.

 

 

Find HOPSON TYRE REPAIR® @ Essen 2016 in Germany during May.24-27, 2016.

Booth Number.: 11H26

 

We are now looking for worldwide agents for HOPSON TYRE REPAIR. If you are interested, please contact us today.

 

General Info:

 

Part No.: F180

Height:3.0mm(include tape 4.0mm)

Width:19mm

Length:194mm

Packing: 52strips/box, 4box/ctn

                  

Description:

 

HOPSON POWER WEIGHT offers a complete range of quality coated, non-coated and adhesive Wheel Weights for passenger cars, motorcycles and trucks. HOPSON Coated Wheel Weights are polyester coated(silver-grey) to prevent material staining on the alloy wheel. HOPSON adhesive wheel weights are pre-cut and require no additional cutting. A simplified organizational system makes wheel weight selection and application easy. Our goal is to become a partner, not just a product supplier. HOPSON POWER WEIGHT guarantee that its products will meet and exceed the highest quality standards in the industry. We are committed to ensuring your success.

 

The steel adhesive strip is individually separable and made up of 12x1/4oz segments.

 

Surface: Zinc plated and Epoxy coated is avaliable.

Installation of Adhesive Weights:

 

Pre-treating the rim:

Clean the rim thoroughly with a cleaning agent that is compatible with varnish(e.g. IPA 70%) in order to remove any residual grease, silicone or adhesive.

Please note: A minimum of 15ºC is required in terms of both the room temperature and the rim temperature.

 

Pre-bending the weights:

Separate the correct gram(as calculated) from the bar. Mould the shape of the weight to match the rim radius(with protective film).

Please note: You need to bend the weights gradually, otherwise they will break apart at the joins. You should bend the weight to a little more than the rim's radius.

 

Removal of the protective film:

Remove the protective film.

Please note: Do not touch the glued surface after peeling off the rim.

 

Sticking the weight on:

Attached the weight to the calculated point on the rim, making sure that the weight is distributed evenly either side and the weight is parallel with the edge of the rim.

Please note: Press down on the weight hard, working from the centre to the left and right. A minimum pressure of 1kg/cm2 is required. The angle of the sticking surface should not be higher than 15 ºC to normal.

 

 

A4 Paper Machine

This is A4 Paper Making Machine,writing and printing Paper Making Machine.

According to the different paper grade and working speed, this kind of Paper Machine is needed to select the way of papermaking, dewatering structure of press section, dryer cylinder bank, sizing and finishing equipments.

Sheet forming can use the open-type headbox, air-cushion headbox, and hydraulic headbox, gap former and inclined wire former. According to the paper uniformity requirement, it can use distributor roll or finishing surface roll.

Press dewatering type is multi-roll and multi-press nip press rather than large-diameter press. As the low basis weight and wet strength of this kind of paper, it usually makes the low strength wet sheet attached to the felt or guide rolls during each section mutual transferring and full web leading as much as possible.

Dryer section: dryer cylinder group. Paper leading: active or passive paper rope system. Finishing equipment: To choose according to the paper grade requirement.

Now we introduce the technical proposal and structural drawing of Fourdrinier advanced printing paper machine, which we made for Taiqian Minrui Huatong Paper Company in Henan province, China. The advanced printing paper of this company is the famous brand in China.

Trimmed width: 2640mm

Working speed: 400m/min

Basis weight: 50-100g/sq.m.

Headbox: Air-cushion headbox

Forming table length: 15m

Suction flat box with all stainless steel micro-crystal cover.

Press section: four rolls two press nips

The wet sheet is stripped by pick-up suction unit.

The second under press nip rubber blind bottom roll diameter is Î¦800mm, with drive unit;

The suction top roll diameter is Î¦800mm, with drive unit.

The top press nip is made by a stone roll and a rubber roll. The rubber roll diameter isΦ800mm, with drive unit;

The stone roll diameter is Î¦850mm, with cut squirt.

This structure ensures the low strength wet sheet can press smoothly and paper breaks can be reduced.

The smooth press rubber bottom roll diameter is Î¦800mm; the top stone roll diameter isΦ850mm. The paper leading roll has the drive unit.

The dryer section has 32 dryer cylinders with the diameter of Î¦1800mm, which is divided into five groups: three groups for before-sizing, two groups for after-sizing. The top and bottom felt of first group and the group at the back of sizing machine is equipped with six felt drying cylinder with the diameter of Î¦1250mm, which can dry the moisture well and improve the drying efficiency.

The paper leading roll has the drive unit. The paper leading type is three-stage passive paper rope system.

Sizing machine: inclined type surface-sizing machine.

Calender: four roll three press nips; the number is decided by the demands.

Reeler: horizontal pneumatic reeling machine.

If you are interested in our products, please feel free to contact us for more information, we are glad to give you the competitive quotation upon receipt of your detailed requirements.

A4 Paper Machine

A4 Paper Making Machine,A4 Paper Machine,Writing And Printing Paper Machine,A4 Copy Paper Making Machine

Dandong Tianshin Automatization Technology Co.,Ltd , https://www.paper-machine.com