Copy Stamford 58 KW Single Phase Hot Sale Dynamo A. C. Sychronous Brushless Alternator 1.Any permanent magnetic generators, providing invariable excitation on all occasions. 2.Easy to be connected with power network or other generators. Standard 2/3 pitch windings check excessive midline current. 3.Balanced rotor with single ball bearing or  two sealed ball bearings 4.Convenient installation and maintenance with easy access to terminals, rotating diodes and coupling bolts 5.Wide range of Flange adaptor and single bearing coupling disc 6. Meet leading Industry and Marine standards Electrical Charcter: Excitation Systerm AS440,SX460,SA465,SX440,SX421,MX341 or MX321 The main stator provides power for excitation of the exciter field via AVR Output power of exciter's rotor is input to that of mains through 3-phase full wave rectifier.Two ends of the rectifier are connected with piezoresistance for restraining surge voltage and avoiding the impact caused by short circuit or parallel synchronization loss. Exciter's Stator is equipped with permanent magnetic steel, it can make generator starting smoothly in any occasions. Voltage regulation(1.0%) and low frequency protection, exterior voltage adjustment of SX440,MX341 and Mx321 suitable for the generator with permanent magnetic generator (PMG) Frame: All industrial standard generators is IP21(NEMA1), also IP23 is optional, But rated power will decrease 5%, Marine standard generators is Ip23. Air filter is optional, but rated power will decrease 5% if installed. Axis and Key All of the generator rotors pass balance test, The vibrations are lower than the minium of BS6861 P.A, G2.5 two bearing generator has a half-key testing balance. Terminal and Terminal Box The three-field generator has 12 leads brought out to the terminals in terminal box. The terminals are put on the non drive end. The box is equipped with removable panels Engine Adaptor and Coupling Disc SY-A Series single-bearing, engine adaptor: SAE0,1,2,3 and 4; Coupling discs: SAE8,10,11,.5,14 and 18 are available. SY-A Series double-bearing, engine adaptor: SAE0,1,2,3,4 and 5 are available. Voltage Regulation: Voltage regulation refers to the change of voltage from non-load to with power factor ranging from 0.8 to 1 and 3%'s fluctuation of the speed of engine. Voltage is adjusted via potentiometer of AVR Applications:It is suitable to match with any brands of the diesel engines in the world, such as USA brand, UK brand, Lovol, Deutz,Volvo Penta,Kubota, Doosan and China made diesel engines. It can be used in land, watercraft, railway, hotel and the places need industry power. Our high-quality reliable AC generators are winning great acclaim from the domestic and abroad power generation market. FAQ : Delivery within 25 days after deposit confirmed.  Copy Stamford 58 KW Single Phase Hot Sale Dynamo A. C. Sychronous Brushless Alternator 1.Any permanent magnetic generators, providing invariable excitation on all occasions. 2.Easy to be connected with power network or other generators. Standard 2/3 pitch windings check excessive midline current. 3.Balanced rotor with single ball bearing or  two sealed ball bearings 4.Convenient installation and maintenance with easy access to terminals, rotating diodes and coupling bolts 5.Wide range of Flange adaptor and single bearing coupling disc 6. Meet leading Industry and Marine standards Electrical Charcter: Excitation Systerm AS440,SX460,SA465,SX440,SX421,MX341 or MX321 The main stator provides power for excitation of the exciter field via AVR Output power of exciter's rotor is input to that of mains through 3-phase full wave rectifier.Two ends of the rectifier are connected with piezoresistance for restraining surge voltage and avoiding the impact caused by short circuit or parallel synchronization loss. Exciter's Stator is equipped with permanent magnetic steel, it can make generator starting smoothly in any occasions. Voltage regulation(1.0%) and low frequency protection, exterior voltage adjustment of SX440,MX341 and Mx321 suitable for the generator with permanent magnetic generator (PMG) Frame: All industrial standard generators is IP21(NEMA1), also IP23 is optional, But rated power will decrease 5%, Marine standard generators is Ip23. Air filter is optional, but rated power will decrease 5% if installed. Axis and Key All of the generator rotors pass balance test, The vibrations are lower than the minium of BS6861 P.A, G2.5 two bearing generator has a half-key testing balance. Terminal and Terminal Box The three-field generator has 12 leads brought out to the terminals in terminal box. The terminals are put on the non drive end. The box is equipped with removable panels Engine Adaptor and Coupling Disc SY-A Series single-bearing, engine adaptor: SAE0,1,2,3 and 4; Coupling discs: SAE8,10,11,.5,14 and 18 are available. SY-A Series double-bearing, engine adaptor: SAE0,1,2,3,4 and 5 are available. Voltage Regulation: Voltage regulation refers to the change of voltage from non-load to with power factor ranging from 0.8 to 1 and 3%'s fluctuation of the speed of engine. Voltage is adjusted via potentiometer of AVR Applications:It is suitable to match with any brands of the diesel engines in the world, such as USA brand, UK brand, Lovol, Deutz,Volvo Penta,Kubota, Doosan and China made diesel engines. It can be used in land, watercraft, railway, hotel and the places need industry power. Our high-quality reliable AC generators are winning great acclaim from the domestic and abroad power generation market. FAQ : Delivery within 25 days after deposit confirmed.
1. What is the a Flatbed Semi Trailer?
Flatbed Semi Trailer is usually used to transport 20ft or 40ft containers, they are mainly used for container transportation supporting ships, ports, shipping lanes, highways, transit stations, bridges, tunnels, and multimodal transport.
Use platform trailers to transfer cargo at the shipper`s warehouse. Unloaded to the consignee`s warehouse, when changing trailer or boat on the way, there is no need to take the goods out of the box and change them.
The size of the container trailer loading area is determined according to the standard container size.A twist lock device for fixing the container is provided at positions corresponding to the four corners of the bottom of the container. Flatbed trailers are a special trailers for transporting containers.
2. What is the common types of container carrier trailers?
Common flat top semi trailer has four types according to the number of axles, which are the 2 axle 40 foot flatbed semi trailers, 3 axle 40ft flatbed trailers, 4 axles 40 foot flat platform truck trailer, and the single point suspension logistics trailer.
According to the different types of transport containers, there are 4 types, 20ft container carrier trailer, 40 foot Shipping Container Trailer, 45ft commercial flat body trailer, and 20/40ft multi-purpose utility trailer.
we can also offer the 48ft, 53ft and other flatbed trailer sizes.
3. Shipping of container flatbed trailers and marine transportation
When transporting flatbed trailers, many customers use container transportation, which has low transportation costs and short transportation time. But the bad thing is that the rear of the platform semi trailer needs to be composed.
Some customers are bulk carriers or ro-ro ships. CHVM commercial flatbed trailers will spray wax and cover the tarpaulin when the cargo ship is bulking.
4. Flatbed semi trailer buying guide
Container flatbed semi trailers can be produced by all factories. When choosing a supplier, many customers do not understand the differences between container flatbed.
The easiest way is to look at the weight. The heavier the weight of flatbed trailers, the better the quality. The tri axle flatbed trailers purchased by African customers self weighs is 7.1 tons. If the weight is only 6.5 tons, the cost of this trailer can save more than 1,000 dollars.
Here are a few more important points:
1. Working platform of container flatbed semi-trailer
The work platfrom is the main load-bearing part, which is composed of the main beam, side beam, cross beam, bottom floor, suspension and so on. The main beam should pay attention to whether the thickness is an international standard. The international standard for the main beam of a container flat semi trailer is 14/8/16 mm. The steel plate in the middle of the beam is made of Q345B manganese steel, the thickness is 8mm. Many unreliable suppliers will use 6mm main beam to save costs. But the carrying capacity was reduced by 26%.
2. Bottom floor of flatbed container trailer
Bottom Floor, many logistics trailer also can transport bulk cargo and other items. The bottom plate of the Titan high bed trailer passes the international standard 3mm thick checkered plate. If it use 2mm thick pattern plate or a 2.5mm bottom plate. It will cost less $ 700. Tri axle equipment trailer weight limit is 60ton capacity.
3. Axle of flatbed truck trailer
The axles of semi trailers for sale have three types: 13-ton axles, 13-ton axles, and 16-ton brake system axles, 16-ton axles.
The axle of the CHVM container flatbed semi trailers is a 13-ton axle and 16-ton brake system axle, which has better braking performance and shortens the braking distance by more than 5 meters.
4. Tire of flat deck trailer
The 3 axle flatbed trailer uses a vacuum tire with better heat dissipation performance, the model is 12R22.5.
CHVM flatbed container uses custom made tires in a tire factory, wear-resistant tires. On Chinese highways, Titan tires can reach more than 300,000 kilometers.
5. Suspension of container flatbed trailers
CHVM flatbed trailers common mechanical suspension adopts special high strength steel. 6mm thickness. The center pin diameter is 70mm. Stronger than suspensions in many factories.
And we also have bogie suspension and airbag suspension for you to choose.
5. What is the manufacturing process of container flatbed semi-trailer?
1. Engineers provide drawings based on platform semi trailer data and customer requirements and then distributed the drawings to the workers in the production department.
2. According to the drawings of each part produced by the design department, use a CNC cutting machine to cut each part, such as the steel plate for the main beam and the reinforcing plate.
3. Welded container flatbed semi trailers work platform, welded side beams, main beams, welded kingpins, welded suspension, welded bottom floor.
4. Flatbed trailers derusting, frosting, spraying primer, spraying paint, wax spraying; installing axles; installing tires.
5. Print VIN code, waiting for packing.
6. How to load and securing a shipping container on a flatbed?
You can use container tipping tilt chassis trailer, it can load by self.
You can use container side loader trailer.
You can use container lift fork.
Flatbed Semi Trailer Flatbed Semi Trailer ,Container Semi Trailer,Flat Bed Semi Trailer,Container Truck Trailer Liangshan Changhong Special Purpose Vehicle Manufacturing Co., Ltd. , https://www.chvehicles.com
Features:
Â
2. What's your payment terms?
1).We accept 30% T/T as the deposit,the balance payment paid before delivery when see the copy of B/L.
2). L/C at sight.
4. What's your warranty & guaranty ?
Warranty is one year or 3000 hours which comes first.Â
5. What's your MOQ?
MOQ  is 10 sets.
6. What's the frequency of diesel generators?
50Hz & 60HZ .
7. What's the voltage of your diesel generator?
Voltage is 220/380V,230/400V,240/415V,110/220V,230/440V, just as per your request.
8.Q:Are you a factory or trading company?        A:  We are a famous manufacturer named MINDONG MINSUN POWER,our engineers are from old MINDONG MOTOR factory .
 9. Q:Where is your factory located?         Â
     A: Our factory is in famous power city-FU'AN CITY,FUJIAN,near Taiwan.It is only 2 hours from Fuzhou airport by car;and 2.5 hours by    train from Xiamen Airport;6 hours from Shanghai Airport by train.
10 .Q:What is the material of your products?  Â
     A: We use AAA Grade Iron or Steel cast and 100% copper wire inside alternator.
 11.Q:How about quality control in your factory?     Â
A: MINDONG MINSUN POWER is a good reputiaon factory. We are always paying great attentions to quality controlling from the beginning to the end.We also have strict testing system and equipments for the all procedure of the production,and three engineers.
12. Can you supply spare parts?
A: Yes, we supply spare parts, if within the warranty, we can offer spare parts free.
13.Q: Is it all right to make customer's own brand name?
A: Yes,we can be your OEM manufacture with your authorization of    brand.
14.Q: What is your company's available production capacity?
A: 5000-10000 pieces per month against your orders.
15.What is your main products and engine brands ,and power range?
A: Our main products are ---
1).Copy Stamford ,brushless alternator from the power 7.5 KVA to 2200 KVA .
2).ST,STC ,TZH carbon brush alternator from 2 KVA to 400 KVA.
3).We also have some famous brands of alternators for your options,such as original STAMFORD,LEROY SOMER,MECC,ENGGA,MARATHON etc. to match famous engines for gensets.
Features:
Â
2. What's your payment terms?
1).We accept 30% T/T as the deposit,the balance payment paid before delivery when see the copy of B/L.
2). L/C at sight.
4. What's your warranty & guaranty ?
Warranty is one year or 3000 hours which comes first.Â
5. What's your MOQ?
MOQ  is 10 sets.
6. What's the frequency of diesel generators?
50Hz & 60HZ .
7. What's the voltage of your diesel generator?
Voltage is 220/380V,230/400V,240/415V,110/220V,230/440V, just as per your request.
8.Q:Are you a factory or trading company?        A:  We are a famous manufacturer named MINDONG MINSUN POWER,our engineers are from old MINDONG MOTOR factory .
 9. Q:Where is your factory located?         Â
     A: Our factory is in famous power city-FU'AN CITY,FUJIAN,near Taiwan.It is only 2 hours from Fuzhou airport by car;and 2.5 hours by    train from Xiamen Airport;6 hours from Shanghai Airport by train.
10 .Q:What is the material of your products?  Â
     A: We use AAA Grade Iron or Steel cast and 100% copper wire inside alternator.
 11.Q:How about quality control in your factory?     Â
A: MINDONG MINSUN POWER is a good reputiaon factory. We are always paying great attentions to quality controlling from the beginning to the end.We also have strict testing system and equipments for the all procedure of the production,and three engineers.
12. Can you supply spare parts?
A: Yes, we supply spare parts, if within the warranty, we can offer spare parts free.
13.Q: Is it all right to make customer's own brand name?
A: Yes,we can be your OEM manufacture with your authorization of    brand.
14.Q: What is your company's available production capacity?
A: 5000-10000 pieces per month against your orders.
15.What is your main products and engine brands ,and power range?
A: Our main products are ---
1).Copy Stamford ,brushless alternator from the power 7.5 KVA to 2200 KVA .
2).ST,STC ,TZH carbon brush alternator from 2 KVA to 400 KVA.
3).We also have some famous brands of alternators for your options,such as original STAMFORD,LEROY SOMER,MECC,ENGGA,MARATHON etc. to match famous engines for gensets.
Copy Stamford 58 Kw Single Phase Hot Sale Dynamo a. C. Sychronous Brushless Alternator
Model NO.: SY-A224F
HS Code: 8501320000
Model NO.: SY-A224F
HS Code: 8501320000