What should you watch when choosing a full-height rotating gate?

Full-height turnstiles are mainly used in places where access to violence is prevented, such as football fields and prisons. Compared with other turnstiles, the main advantages of full-height turnstiles are: Solid, impact-resistant and cannot be illegally exceeded. When choosing a full-height rotary turn machine, you need to pay attention to the following aspects:

1. Sturdy and impact resistant: The turn bar and the outer guardrail need to be sturdy and able to withstand large destructive forces.

2. Security: The biggest concern with full-height turnstiles is that the audience is locked in the gate and cannot enter or exit. In any case (such as a sudden power failure) must avoid this situation, rely on the principle of design.

3, arm weight, inertia, when the arm is in place, there should be no oscillation phenomenon.

4. Reliability: The reliability of the gate is based on the reliability and integration of the various components of the gate. The selection of good quality components is the basis, such as card readers, controllers, monitors, etc.; the integration method mainly depends on the design selection and communication method of the control unit. The presence or absence of lightning protection components also affects the reliability of the equipment.

5. Rotational life: There will be wear on moving parts, and the design and selection of key components is reasonable.

6, the bar code reader above the glass material: above the bar code reader must be transparent, the use of organic glass is low cost, easy processing and installation, but after many brush votes, the glass will wear rough, affect the bar code reading speed and accuracy Therefore, wear-resistant quartz glass must be used;

7. Checking speed: The large flow rate of gates is used, and the passing speed of ticket checking is an important indicator. The speed of ticket checking depends on the control mode of the gate, communication network, ticket processing software, and the speed of mechanical action. In general, the gate response speed is within 500ms.

Wire surface treatment machine
Wiping machine

Power supply voltage 380 volts 50-60HZ

0.75 kW of power used

Wire wheel diameter 420mm, R groove fully sprayed with nano wear-resistant ceramic

The polishing unit has a pressure equalization adjustment device, and the pressure is adjustable

Polishing unit reciprocating frequency 7 times per minute

Applicable steel wire diameter 0.7-1.5mm

applicable steel wire speed â‰¤ 1200 meters per minute

Machine dimensions: 2 meters X 0.9 meters X 1.36 meters

In order to ensure that the surface of the pulled steel wire is clean and powder-free, a cleaning equipment device is used for cleaning treatment. An appropriate (usually 1%) metal surface treatment agent is added to tap water, and the surface of the steel wire is washed by a high-pressure submerged pump (1.1KW). At the same time, a cleaning ball is used to wipe the surface of the steel wire in the passage. In order to ensure that the surface of the steel wire is wrapped without water before entering the winding line, So, at the outlet of the steel wire, a high-pressure air blowing device is used to vigorously blow the steel wire surface 360 Â° without gaps, ensuring that there is no water vapor in the steel wire during winding. This cleaning machine is divided into two layers: upper and lower, with a steel wire passage layer on top. The specification is 400X300X2000, which is made of stainless steel welded material. Inside, there are nine adjustable cone wiping devices, which tightly contact the steel wire and the cleaning ball for wiping; The lower layer is a water storage tank, with a specification of 800X700X1600, which is welded from 4mm stainless steel plate. There is a filtering area in the water tank, and the filtered water is pumped out from the anti-corrosion liquid pump on the water storage tank into the upper aisle water tank for flushing. The underwater pump will not block and has a longer lifespan. The lower water tank is equipped with a decontamination hole to remove debris and garbage. According to customer needs, in areas where the weather is too cold, an electric heating system or a steam heating system can be installed on the water tank, and the heating temperature can be designed to maintain a certain temperature for flushing and wiping with water.
wire polishing machine,surface cleaning machine
Jiangyin Wanyi Machinery CO.,Ltd , https://www.wydrawmachine.com